DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 by DAOKI at Buditech. MPN: FBA_TS-US-078-SNL. Hurry! Limited time offer. Offer valid only while supplies last. L298N is a kind of high voltage,high current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high
L298N is a kind of high voltage,high current motor driver chip produced by ST company.Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A,continuous working current 2A) and 25W of rated power.Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor,relay coil and so on.Using standard logic level signal control,it has two enable control ends.It permits or prohibites device having a logic power supply input without the impact of input signal,which enables the internal logic circuit part works at low voltage.The chip can connects to external detecting resistor to give the variations to the control circuit.Using L298N chip to drive the motor,this chip can drive a stepping motor or four phase stepping motor,and two DC motors as well.
1.Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.
2.This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.
3.Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability .
This module is integrated with a built-in 5V power.When the drive voltage is 7V-35V, it can enable the onboard 5V logic power supply;afterthe power supply,don't input voltage in the interface+5V power supply,but you can lead the 5V for external use.
when ENA enable IN1 IN2 control OUT1 OUT2
when ENB enable IN3 IN4 control OUT3 OUT4
1.Driving stepper motor
The connection of driving a common 4 line 2 phase electric motor is shown in below figure
after enable ENA ENB
Features & Highlights
- The signal is shown in the figure
- The connecting method is shown inbelow figure after enable ENA ENB
- Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.
- Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled
|Item Weight:||0.35 pounds|
|Package Weight:||0.35 pounds|
|Package Size:||4.7 x 1.9 x 1.9 inches|
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by DAOKI, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
Yakamoz L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino Feature: - Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-in...
mpn: DE L293D, ean: 0520141421347,
Introduction This is a module commonly used for DC motor drive. The pins work with Arduino boards, which enables hobbyists make Arduino development projects conveniently. It adopts L293D chip for small-current DC motor drive. Two such chips are used ...
mpn: 101, ean: 0615867613975,
12V-24V Pulse Width PWM DC Motor Speed Switch Controller Regulator Description::: Control the speed of a DC motor with this controller Control the light of a lamp with this controller High efficiency, high torque, high power, high heat dissipation Wi...
By KB Electronics
KB Electronics 9340 - KBPC-PW-AC Run-Stop-Jog Switch KitBrand New Genuine KB Electronics Parts. Factory Authorized KB Electronics Distributor. Tech Support on all products purchased from us.. ...
mpn: b7488e7fa4fb98d9b70a7c14837d0064, ean: 0023981611348,
Description:DC 12V 24V 36V 48V DC Motor Speed Controller.High efficiency, high torque, low heat generating.Control the speed of a DC motor with this controller.40A high power forward and reverse speed switch. Positive and negative polarity relay swit...
mpn: TXJ-061-US, ean: 0611702529715,
L298N of TIMESETL TIMESETL Motor Drive Controller - High Quality Specification: Size: 43*43*27mm/ 1.69*1.69*1.06 inch Dual H bridge drive (can drive 2 DC motors) Chip: L298N Logical voltage: 5V Drive voltage: 5V-35V Logic current: 0mA-36mA Drive cur...
By DL Wholesale
mpn: 950001, ean: 0816731010757,
Speed Bully Motor Speed ControllerIncludes Factory Warranty. Includes Full Warranty. ...
The motor driver controller can be applied to DC brushed motor speed regulation, light dimming regulation in DC circuit. The advantage of using a pulse width modulation (PWM) method for dimming / speed regulation is that the energy of the power suppl...
mpn: TK0337, ean: 0700253197266,
Sunweb™ - Let Shopping become easier! 100% Brand New.Drum Switch--for Motor Control or High Current SwitchingContact Rating: 0 to 380V, 60A (3HP 120V or 6HP 240V Motors)Switch Action: Maintained (Stay Switched)Casing: Impact and Corrosion Resistan...
mpn: d20170520xj0023, ean: 7523427762434,
Working Voltage: DC10V-30V(Broad Voltage) Controlling Power: 12V*3A=36W,24V*3A=72W,... Rated Current:3A MAX Current:4A Speed Rate Range:5%-95% PWM Freguency:500Hz Size:74mm*47mm*28mm Weight:67g Potentiometer: B10K;20cm cord length;hole size 8mm Pleas...